AeroKing Vertical Tine Aerators
Quick and effective aeration and compaction relief
- The ‘Autoheave’ system is both simple to set up and operate
- Height is controlled by interconnected handles from either the right or left hand side of machine
- three speed gearbox is standard on all models for fine control of hole spacing on tractors with 540, 750 or 1000 rpm PTO shafts.
- Machine weight can be increased by water ballasting the rollers if required
- Simple and strong engineering for maximum service life and minimum down time and servicing
- Close coupling to the tractor keeps tractor lift capacity to a minimum. An optional trailed version is available for high horsepower tractors with low lift capacity.
|
|
|
Three ranges:
- 300-50 - for tractors from 20-50hp, 1.2m and 1.65m working widths, and a lighter weight ‘A’ version for small tractors. Tine length 180/300mm (7”/12”).
- 300-80 - for tractors from 35-80hp, 1.65m or 2.1m working widths, and a lighter weight ‘A’ version for small tractors. Tine length 180/300mm (7”/12”).
- 400-95 - for tractors from 45-95hp, 1.7m, 2.1m and 2.5m working widths. Tine length 300/400mm (7"/12"/16”).
Solid tines range from 8-25mm (5/16-1”) in diameter and hollow tines from 16-25mm (5/8-1”) in diameter allowing for use on most turf surfaces with minimal surface disturbance.
|
AeroKing patent operation with ‘Autoheave’
Unlike conventional vertical tine aerators, the AeroKing’s parallel action uses a single compression spring on the top drive arm, as opposed to twin springs on the bottom arm, which can actually prevent a machine’s heave action. The heave action on the AeroKing is completely automatic and is governed by the hole spacing and tractors forward speed. The patented top spring system and irregular parallel action mean the tines are driven into the ground and start the heave action and are only assisted on the return stroke out of the ground by the single compression spring. This combined with the unique working path of the tine holder keeps the edges of the hole more uniform with less pressure on the sides of the hole, and less wear and tear on the machine.
|
|
Model |
|
Working
width
mm |
Weight
kg |
No. of tine
carriers |
Min/Max
hp |
300.50A |
1204
1656 |
1200
1650 |
480
650 |
4
6 |
25/50
35/50 |
300.50 |
1204
1656 |
1200
1650 |
580
770 |
4
6 |
25/50
35/50 |
300.80A |
1656
2108 |
1650
2100 |
710
880 |
6
8 |
40/80
50/80 |
300.80 |
1656
2108 |
1650
2100 |
830
1020 |
6
8 |
40/80
50/80 |
400.95 |
1706
2108
2510 |
1700
2100
2500 |
930
1160
1380 |
6
8
10 |
45/95
55/95
70/95 |
Standard specification includes three speed gearbox, PTO shaft with slip clutch, Cat 1 and Cat 2 3 point linkage, front roller with water ballasts for depth adjustment, patented Autoheave system
Tines and Accessories
Tines
|
Ø x length mm |
No. per carrier |
Solid tines |
8 x 180
12 x 300
18 x 300
18 x 400†
25 x 300
25 x 400
|
4* or 8***
4
2**
2**
2
2
|
Hollow tines |
16 x 175
19 x 255
25 x 255 |
4
2**
2** |
Adaptors |
from 12 to 8mm (for * above)
from 25 to 18mm (for ** above)
|
Multiplier |
for 8 times instead of 4 (*** above) |
| † |
400 mm length tines on 400.95 models only |
| |
25 to 18mm adaptor on 400.95 models only |
Accessories:
- Rear roller with water ballast.
- Hydraulic trailer for transportation.
- Brushes (2) and roller for levelling sand/filling in.
- Hydraulic rotating brush and roller.
- Adjustable windrow plates for cores.
- Wide turf retaining plate for use with soft turf.
- Narrow turf retaining plate for use with soft turf.
Mowers  Mower Collectors Scarifier Collectors Sidearm Flail Mowers Multi-Use 4 in 1 Flail Mowers
Hedge and Verge Mowers Forestry Mulchers Log Splitters Vacuum Collector Sprayers
|
